Glue Support Primer Accelerator - Strong Adhesive Booster for Crafts, Woodworking & DIY Projects - Fast Drying & Enhanced Bonding
Free shipping on all orders over $50
7-15 days international
10 people viewing this product right now!
30-day free returns
Secure checkout
14643298
Description
Glue Support Booster is a 2 in 1 product, specially designed to prepare the surface of the natural lash by providing optimal conditions for glue adhesion between the extension and natural lash. It also acts as an accelerator by providing the catalyst required for the glue to cure faster.
Fast Facts:
- PLA primer or accelerator
- 10 mL bottle
- 100% vegan
Glue Booster Primer
Glue booster provides the optimal conditions necessary for the lash extension without over-drying or stripping the natural lash of oils.
Glue booster is designed to prepare the natural lash by providing the optimum pH required for the glue to grab without much effort. Glue booster is ideal for clients with oily skin or where glue may not be grabbing the lash.
How to Use as a Primer:
- Cleanse lashes and thoroughly rinse and dry
- Apply a small amount of booster onto 2 clean micro brushes-do not oversaturate
- Apply to all areas where lash will be bonded-careful not to touch the skin
- Allow drying for 2 minutes before application.
- Proceed as normal with lash application
Can be used as a Glue Booster Accelerator
For advanced artists only.
In suboptimal humidity conditions adhesive will cause slower cure time and poor adhesion due to the lack of water (OH molecules from water). Applying a small amount of glue booster to the strip will speed the cure time of any adhesive.
Caution: booster may only be applied to regular volume or single lash trays and NOT easy fanning lashes.
How to use as an Accelerator:
- Wet a micro brush with a small amount of booster
- Remove as much booster off the brush onto a clean towel
- Rub the working section (small) of the lash tray. The booster should barely be visible
- Allow to dry
- Proceed to make fans and dip in glue
Note: glue will require changing more often due to the presence of booster on the extension.
Check out or Facebook or Instagram for videos on how to properly use Glue Support.
Liquid products, including adhesive, primers, bonders, and cream based products cannot be returned.
MSDS
Section 1 – Chemical Product and Company Identification
MSDS NAME | Glue Support 2 In 1 |
COMPANY ADDRESS | 1285 Financial Blvd Reno, NV 89502, USA Tel:775-440-1208
|
|
|
Section 2 – Composition and Ingredient Information
Ingredient Component Name
Ethanol
CAS Number 64-17-5
Concentration 30%
Glycerin
CAS 56-81-5
Concentration 10%
Carbomer
CAS Number 9007-20-9
Concentration 0.5%
Water
CAS Number 7732-18-5
Concentration 85%
Triethanolamine
CAS Number 102-71-6
Concentration 2.5%
Fragrance
CAS Number 35206-51-0
Concentration 1%
Section 3 – Hazards Identification
Hazard Risk Classification | Category 1 |
Flammability | 2 |
Physical Hazard | 1 |
Potential Health Effect | Eye: Irritating to eyes. Causes excessive tearing. Eyelids may bond
Skin: May cause skin irritation Inhalation: May cause respiratory tract irritation. The toxicological properties of this substance have not been fully investigated
Ingestion: Not expected to be harmful by ingestion. Rapidly polymerizes (solidifies and bonds in mouth. It is almost impossible to swallow. |
|
|
WARNING : MAY CAUSE EYE AND RESPIRATORY IRRITATION BONDS SKIN IN SECONDS.
Relevant routes of exposure: Inhalation, Eyes Potential Health Effects Inhalation : Exposure to vapors above the established exposure limit result in respiratory irritation which may lead to difficulty in breathing and tightness in the chest | |
Section 4 – First Aid Measures
Inhalation | Remove to open space with fresh air. Seek medical attention to treat symptomatically if discomfort persist. Keep eye covered until deboning is complete, usually within 1-3 days. Medical attention should be sought in case the liquid trapped behind eyelid caused abrasive damage.
|
Eye Contact | Non provided
|
Skin Contact | In case of unexpected irritation, immediately wash skin with soap and large amounts of water
|
Ingestion | Ingestion is not likely. See supplemental page for emergency procedures.
|
|
|
Section 5 – Fire Fighting Measures
Flash Point | 29℃ (85 deg F) Tagliabue closed cup
|
Auto Ignition temperature | 485℃ |
Flammable/Explosive Limits-lower% | Not determined
|
Flammable/Explosive Limits-upper% | Not determined
|
Hazardous Decomposition Materials | N/A
|
Suitable Extinguishing Media | Dry powder. Foam and Water spray. Carbon dioxides.
|
Protective Equipment | Fire fighters should wear positive pressure self-contained breathing
|
Hazardous combustion products | Trace amount of toxic and or irritating fumes may be released and the use of breathing apparatus is recommended.
|
Unusual fire or explosion hazard | None
|
Specific Hazard(s) | Trace amount of toxic and or irritating fumes may be released and the use of breathing apparatus is recommended.
|
Section 6 – Accidental Release Measures
General Information | None provided
|
Environmental precautions | Ventilate Area
|
Disposal and Clean Up | Do not use cloths for mopping up. Flood with water to complete polymerization and scrape off the floor. Cured material can be disposed of as non-hazardous waste |
Section 7 – Handling and Storage
Handling Precautions | Avoid contact with eyes. Avoid breathing of vapors
|
Storage | Keep in a cool, well ventilated area away from heat
|
Section 8 – Exposure Controls and Personal Protection
Engineering Controls | Use positive down-draft exhaust ventilation if general ventilation is insufficient to maintain vapor concentration below established exposure limits. Respiratory
|
Respiratory Protection | Use NIOSH approved respirator if there is potential to exceed exposure limits. Observe OSHA regulations for respiratory use (29 CFR 1910.134)
|
Skin Protection | N/A
|
Eye/Face protection | Chemical splash goggles or safety glasses with side shields.
|
General Hygiene measures | N/A
|
Section 9 – Physical and Chemical Properties
Physical State | Transparent liquid |
Odour | Aromatic |
pH | N/A |
Specific Gravity | 1.04 @ 75oF |
Boiling Point | 78.2OC |
Flash Point | Not available |
Flammability | Not available |
Evaporation Rate(Ether=1) | N/A |
Ignition Temperature | Not available |
Melting/Freezing Point | Not available |
Solubility | Polymerized by water |
Vapour Density | Approximately 3 |
Vapour Pressure | Less than 0.2mm |
Volatile Organic Compound(EPA Method24) | 87..9% |
Section 10 – Stability and Reactivity
Stability | Stable under recommended storage conditions
|
Conditions to Avoid | Spontaneous polymerization
|
Incompatible Materials | None listed
|
Hazardous Polymerization | Rapid exothermic polymerization will occur in the presence of water, amines and alcohols
|
Hazardous decomposition | None listed
|
Section 11– Toxicological Information
Product toxicity data : Acute oral LD505000mg/kg(rat) Acute dermal LD502000mg/kg(rabbit)
Hazardous component | NTP Carcinogen | IARC Carcinogen | OSHA |
Ethyl Cyanoacrylate 7058-85-0 | NO | NO | NO |
Carbon Black 1333-86-4 | NO | Group 2B | Yes |
|
|
Section 12– Ecological Information
Not known
Section 13– Disposal Consideration
No data available
Section 14– Transport
INTERNATIONAL AIR TRANSPORT ASSOCIATION (IATA) :
This product is not classified as dangerous goods , by rules of IATA. U.S Department of Transportation (DOT) Shipping regulations:
This product is not classified as dangerous goods, per U.S. DOT regulation under 49CFR 172.101.
Proper shipping name : Volume X
Hazard Class number and description : Not applicable. UN identification number : Not applicable.
Packing group : Not applicable.
Section 15– Regulatory Information
United State Regulatory Information
TSCA 8 (b) Inventory Status : All components are listed or are exempt from listing on the Toxic
Substances Control Act Inventory TSCA 12(b) Export Notification : None
CERCLA/SARA Section 302 EHS : None
CERCLA/SARA Section 311/312 : Immediate Health Hazard, Delayed Health Hazard, Fire.
Reactive
CERCLA/SARA 313 : None
California Proposition 65 : No California Proposition 65 listed chemical are known to be present Canada Regulatory Information
All components are listed on or are exempt from listing on the Domestic Substances List WHMIS Hazard class : B.3, D.2.B
Section 16– Other Information
DISCLAIMER :
All the information of Material Safety Data Sheet is provided on the basis in good faith, and is believed to be trustworthy but is for reference only.
BTC and its agents, dealers, distributors, directors and employees do not accept any liability for the results whatsoever arising from the use of BTC products due that the utilization of these products is simply out of BTC control. The users are responsible for selecting the suitability of the products and methods of use.
